Bar Sink Installation Near Me
Starting price: Call for pricing
A bar sink turns a home bar, butler's pantry, or kitchen island into a genuinely useful workspace — for rinsing glassware, prepping garnishes, and keeping drink duty out of the main kitchen. Plumbing Services Pros installs drop-in, undermount, and vessel bar sinks with full hot and cold supply lines, a proper P-trap drain, and correct venting. You pick the sink and the spot; we handle the plumbing underneath.
What a bar sink installation involves
A bar sink is a small secondary sink — usually 12 to 18 inches wide — set into a home bar, kitchen island, or butler's pantry. Despite the size, the plumbing behind it is the same as a full-size sink: hot and cold supply lines, a drain with a P-trap, and a vent that keeps the drain flowing smoothly. Installing one is real plumbing work, not just setting a basin in a hole.
The job changes a lot depending on location. Replacing a sink where plumbing already exists is straightforward. Adding a bar sink where there's never been one means running new supply lines and a drain across the room, through cabinets or the floor, and tying everything into the existing system. That routing is the part that takes a plumber's eye — and often a permit.
Picking the right sink for the space
- Drop-in (top-mount): sits on the counter with a visible rim — the easiest to install and swap later
- Undermount: mounts beneath a stone counter for a clean look and easy wipe-down
- Vessel: a bowl that sits on the counter — bold style, but needs a taller faucet
- Copper or hammered finishes: eye-catching for entertaining spaces, and they patina over time
Scale matters more than style. A bar area that's only a few feet long shouldn't lose a third of its counter to the sink. We help you match the sink size to the space, and we flag clearance needs — like making sure the cabinet below has room for the trap and shutoffs.
How the installation goes
We start by marking the sink location and confirming what's underneath — joists, existing pipes, anything in the way. If supply and drain lines need to run, we plan the shortest clean route to the existing plumbing. Then we shut off the water and get to work.
New supply lines get run in and connected with individual shutoff valves at the sink. The drain gets a P-trap — the curved section that holds water and blocks sewer gas — tied into the waste line with the right slope, plus a vent connection so the drain doesn't gurgle or siphon. Then the sink is set: sealed to the counter, faucet mounted, drain assembly connected.
Finally, we pressurize everything and check every joint for leaks, run water through the drain to confirm it flows well, and clean up. You get a sink that's ready to use the moment we leave.
What affects the cost
The sink you choose is one factor — a basic stainless drop-in and a hand-hammered copper vessel are very different purchases — but the bigger variable is the plumbing run. A sink going into an existing wet bar with lines already roughed in is a short job. One going into a dry island across the room needs new supply and drain lines, and that labor is where the cost lives.
Cutting and patching adds up too: opening a floor or wall to run pipe, then closing it back up. Access from a basement or crawl space underneath keeps things simpler. Permits and inspections, where required, also factor in.
Call (833) 513-2401, tell us where the sink is going and what's underneath, and we'll give you a straight answer on what the job takes.
Where a bar sink makes sense
Plumbing Services Pros installs bar sinks across the greater Stockton area — in home bars, kitchen islands, butler's pantries, outdoor kitchens, and pool houses. Anywhere you'd rather rinse a glass on the spot than carry it across the house, a bar sink earns its keep.
If you've got the counter space and a vision, call (833) 513-2401. We'll tell you honestly whether the plumbing side of your plan is simple or involved, and handle it either way.
Features
- Hot and cold supply lines run to your new bar sink location
- P-trap drain assembly tied into the existing waste line
- Vent connection sized and placed to code
- Drop-in, undermount, and vessel bar sink mounting
- Faucet installation and supply hookup included
- Shutoff valves added at the sink for easy service
- Leak check on every connection before we leave
Benefits
- A working wet bar without hauling glassware to the kitchen
- Drains fast and quietly thanks to proper venting
- No leaks under the cabinet from day one
- Sink and faucet positioned for comfortable use
- Plumbing hidden cleanly inside the bar or island
- A second sink that actually adds value to the space
Frequently asked questions
Can you add a bar sink where there's no plumbing?
Yes — that's the most common version of this job. We run new hot and cold supply lines and a drain with proper venting from your existing plumbing to the new location. The longer the run and the more surfaces we cross, the more involved the work.
Does a bar sink need a vent?
Yes. Every fixture drain needs a vent to keep water flowing smoothly and sewer gas out. We tie the bar sink's vent into the existing vent system or add one to code.
What size bar sink should I get?
Match it to the counter. A small bar area does well with a 12- to 15-inch sink that leaves working room around it. Your plumber can confirm the cabinet below has space for the trap and shutoffs before you buy.
Drop-in or undermount — which is better?
Drop-in sinks are simpler to install and replace, and they work with any countertop. Undermounts look cleaner and make wiping crumbs into the sink easy, but they need a solid-surface counter and more careful installation. We'll install either.
How much does bar sink installation cost?
It depends mostly on the plumbing run — new supply and drain lines cost more than swapping a sink where lines already exist — plus the sink and faucet you choose. Call (833) 513-2401 for an exact quote on your layout.